Problem with RTK6

[cromwell]

Could some of these instructions be the solution for me?
I have only connected 2 cables, B3 to plus rotating light and A3 to minus on light. I think that more must be connected to work... correct me if I am wrong!






St.2 (Kennleuchte Nr.4 - Zusatzkennleuchte hinten Beifahrerseite)


A1 Ausrüstungserkennung Codierleitung 1
A2 Referenz GND Codierleitungen/Rotations-Kontrolle
A3 Minus für Lastkreis Kennleuchte
B1 Ausrüstungserkennung Codierleitung 2
B2 Kombileitung Synchronisation/Rotations-Kontrolle
B3 geschalteter Plus für Lastkreis Kennleuchte



bei KL-DC:


A1: braun-weiß
A2: braun-weiß + braun
A3: braun
B1: unbelegt
B2: weiß
B3: schwarz



bei KL-XR:


A1: unbelegt
A2: braun-weiß
A3: braun
B1: braun-weiß
B2: blau (Syn.)
B3: schwarz



bei sonstiger Kennleuchte als 3. oder 4. Zusatzkennleuchte (auch Fremdhersteller):


A1: Brücke zu A2
A2: Brücke zu A1 und B1
A3: RKL-Minus
B1: Brücke zu A2
B2: unbelegt
B3: RKL-Plus

[Freestyle]

Zitat von cromwell

Could some of these instructions be the solution for me?
I have only connected 2 cables, B3 to plus rotating light and A3 to minus on light. I think that more must be connected to work... correct me if I am wrong!


bei sonstiger Kennleuchte als 3. oder 4. Zusatzkennleuchte (auch Fremdhersteller):


A1: Brücke zu A2
A2: Brücke zu A1 und B1
A3: RKL-Minus
B1: Brücke zu A2
B2: unbelegt
B3: RKL-Plus

Try this above KL3 or KL 4 but no Garanty

[Blaulicht]

OMG

[cromwell]

What does user Blaulicht think about this? OMG??
I have not tried this last advice yet.. could something go wrong??

[cromwell]

Attention RTK6 experts!
Should I go ahead and connect my 2 rotating-lights like this? :



A1: Brücke zu A2
A2: Brücke zu A1 und B1
A3: RKL-Minus
B1: Brücke zu A2
B2: unbelegt
B3: RKL-Plus

[Freestyle]

Zitat von cromwell

Attention RTK6 experts!
Should I go ahead and connect my 2 rotating-lights like this? :



A1: Brücke zu A2
A2: Brücke zu A1 und B1
A3: RKL-Minus
B1: Brücke zu A2
B2: unbelegt
B3: RKL-Plus

This switch is for 3. or 4. Beacon.
Also for other Rotation Lights like your's.

A1: Bridge to A2
A2: Bridge to A1 and B1
A3: Beacon -
B1: Bridge to A2
B2: Not used
B3: Beacon +

[cromwell]

Yes, now it works!
Thanks to user Freestyle and others for helping me out with this rotating-light issue!

I put a towel in the sirenspeaker pipe to lower the sirensound a bit and it works. But there are now 4 big pieces flashing in the control-unit display to the left.. Has it something to do with siren beeing muffled?? or what?

Lights and siren seems to work fine even with the display flashing.